Corrugated heating pipes
CORRUGATED HEATING PIPES 25mm MADE OF HIGHEST QUALITY POLYPROPYLENE
These pipes allow keeping lower average temperature in a facility comparing to typical convection heating (steel pipes on sides and top of gardening facilities).
Consequently, this results in fuel savings.
CORRUGATED HEATING PIPES ARE AVAILABLE IN TWO QUALITY CLASSES
PREMIUM class: | maximum emergency temperature | 120°C | |
maximum operational temperature | 80°C | ||
material: | PP polymer H 4122 | ||
STANDARD class: | maximum emergency temperature | 90°C | |
maximum operational temperature | 60°C | ||
material | coloured PP polymer |
APPLICATION
Corrugated heating pipes are used for vegetative heating systems, put directly on the ground or buried.
Thanks to such placement they ensure heat, where it is needed the most.
Optimum heating can be ensured by a system with an operational temperature 5-10°C higher than required for particular facility.
ADVANTAGES
- wall thickness 0,9mm reduces heat flow resistance and in turn ensures efficiency of corrugated heating pipe comparable with steel pipes
- special shape of corrugated heating pipe assures proper mechanical resistance while the wall thickness is smaller than for normal PP pipes
- large heating surface contact area with air is approximately 2 times bigger (1412cm2/1m) than in case of standard PP pipes (785cm2/1m). Having ability to use thinner wall results in ~30% higher heat dissipation comparing to standard PP pipes.
- increased mechanical and thermal resistance corrugated heating pipes are designed for maximum operational temperature 60/80°C and maximum operational pressure 2.5 bar
- quick assembly
POWER CONVERSION
40W/mb in systems supplied with 40°C water
80W/mb in systems supplied with 70°C water
MAXIMUM LOOP LENGTH: 100mb
PACKAGING
Pipes are packaged in coils of 250 and 500mb.
ASSEMBLY
Corrugated heating pipes, no matter what quality class, can be assembled in one of the following ways:
1. During replacement of current plain pipe with corrugated one, existing tightened connectors can be used (often installation or also used for hydrating).
Notches are in form of rings, not spiral so in most cases such assembly doesn't carry a risk of spills.
It depends however on technical condition and type of tightened connectors.
2. For new systems we suggest to use our dedicated solution, which is based on special corrugated gaskets and spigots (depending on needs can be made in two versions- for inserting into 3/8" valve or to be welded directly into collector).
Such assembly is very quick and tight, also when version with spigot for welding is applied - definitely the cheapest.
In order to assemble the system you need to mount the gasket into pipe's ending and put the whole set on steel spigot welded into collector or screwed into a valve.
FIXING OF DAMAGED HEATING SYSTEM
In order to connect pipes together or quick repairs (e.g. fixing of a cut pipe) we recommend special double spigots, which together with corrugated seals allow repairing installation in a few minutes. It is enough to cut the pipe completely in a place of damage, put on both sides corrugated seals, and push both on plastic double spigot.
CONSTRUCTING OF TEMPORARY INSTALLATION WITH PLASTIC COLLECTOR
You can quickly assembly system with plastic collector very quickly using special seals from our offer (e.g. using widely available construction PE pipes). In order to do that you need to drill a whole O19mm in a collector, mount special seal and push plastic double spigot. Having a collector prepared in such way you can mount heating pipes directly to it.
NOTE
You can use mild washing liquid or soap while assembling pipe and corrugated seal. Never use grease.
NOTE
In order to use heating pipes for benches it is required to use additional mounting elements, which keep pipes around 2cm above capillary mat or tub. It allows reducing evaporation and increases heating efficiency.
MOUNTING ACCESSORIES
|
![]() |
Corrugated seal |
Steel spigot for welding, black |
|
|
Screw-in steel spigot for 3/8" valve, galvanized |
Double plastic spigot |
|
|
Seal for plastic collector |